Home / Monthly salt and cost estimator

Monthly salt and cost estimator

Once you know the daily grain load and the usable capacity of the unit, you can estimate how often it will regenerate, how much salt that takes, and what the bags will cost at the price you actually pay.

Household water use

The 82-gallon starting figure is total domestic use per person from the USGS 2015 estimate, also cited by EPA WaterSense. EPA WaterSense reports that roughly 70 percent of household use is indoors. If outdoor taps bypass the softener, leave the share at 70, or enter a better number. If the softener treats all household water, set the share to 100. A water bill (gallons divided by days) is better than any average. Leave the bill field blank to use the per-person estimate.

Hardness, iron and cycle

ppm or mg/L is converted at 17.1 ppm per grain per gallon (the usual rounding of the Maryland Geological Survey figure of 17.118). The iron multiplier starts at 4 because the University of Minnesota Water Resources Center states that removing iron with a softener uses about 4 times more sodium than removing hardness ions. Some manuals use 5. Change it to match your manual. Minnesota also notes that softeners may remove up to 3 mg/L of iron, and that a unit should typically work 3 to 5 days without regeneration. Oxidized (red) iron can clog resin and may need a filter first (Penn State Extension).

Your softener and the salt you buy

Usable capacity should come from the manual at the salt dose you will actually use. The efficiency field starts at 3,350 grains per pound, the minimum in the voluntary NSF/ANSI 44 efficiency rating restated by EPA WaterSense and by the DOE Building America Solution Center. That is a benchmark, not a measurement of your unit. If you know the pounds of salt per regeneration from the manual, switch the menu and enter that dose instead. Bag size and price are what you actually buy; the $8.00 starting price is an example, not a survey of store prices. Leave the regeneration-water field blank if you do not have a figure from the manual. This site does not invent one.

How salt use is calculated

Regenerations in the period equal (daily grains times days) divided by the usable grain capacity. Salt used equals regenerations times the pounds of salt per regeneration. If you enter a salt efficiency instead of a dose, pounds per regeneration equal usable capacity divided by grains removed per pound of salt.

The efficiency field starts at 3,350 grains per pound. That number is not a typical-home average. It is the minimum rated salt efficiency in the voluntary NSF/ANSI 44 efficiency rating for residential cation exchange softeners, as restated by EPA WaterSense and by the DOE Building America Solution Center. The same rating requires demand-initiated regeneration and no more than 5.0 gallons of water per 1,000 grains of hardness removed. Your manual may list a higher or lower efficiency at the dose you choose. A higher grain-per-pound figure means less salt for the same work.

Worked example

Using this page's starting household (the same 2,296 daily grains as the grain-capacity default), a usable capacity of 24,000 grains, 3,350 grains per pound, a 30-day month, a 40-pound bag, and an example price of $8.00 per bag: the unit regenerates 2.87 times, uses 20.6 pounds of salt (0.51 bags), and costs $4.11 in that month. The $8.00 figure is only an example so the arithmetic can be shown. Replace it with what you pay.

Sources

Common questions

Why is the starting bag price $8.00?

So the form has a number to compute with. It is not a survey of store prices and it is not a recommendation. Type the price on the bag you buy.

Can I estimate a year instead of a month?

Yes. Set the period to 365 days. The same daily grain load and capacity are used; only the length of the period changes.

Does a lower salt dose always cost less?

A lower dose usually removes fewer grains per regeneration, so the unit may regenerate more often. Enter the usable capacity and the salt dose that go together on the same line of your manual, not a high capacity paired with a low dose.

Estimates only. These tools are for planning, not a quote, a water test, or professional advice. Confirm hardness and iron with a laboratory or your water quality report. Compare the grain result to the capacity listed in the unit's manual at the salt dose you will actually use, which is often lower than the number printed on the box. This site does not sell equipment or take a cut from any brand.

By James Johnston. Updated November 2026. Estimates for planning, not advice. See sources and method.